85 lines
3.9 KiB
C
85 lines
3.9 KiB
C
|
#define DISABLE_ALL_LIBRARY_WARNINGS
|
||
|
|
||
|
|
||
|
#define ST7789_DRIVER // Full configuration option, define additional parameters below for this display
|
||
|
// modified by ZH
|
||
|
#define TFT_WIDTH 240 // ST7789 240 x 240 and 240 x 320
|
||
|
#define TFT_HEIGHT 240 // ST7789 240 x 240
|
||
|
// added by ZH
|
||
|
#define TFT_CS 40 // Chip select control pin, use -1 if not in use or 40 as it does not complain then
|
||
|
#define TFT_DC 3 // Data Command control pin
|
||
|
#define TFT_RST 2 // Reset pin (could connect to RST pin)
|
||
|
#define TFT_MOSI 4
|
||
|
#define TFT_SCLK 5
|
||
|
#define TFT_MISO 40 // not in use, use -1 if not in use or 40 better as it does not complain then
|
||
|
|
||
|
|
||
|
// ##################################################################################
|
||
|
//
|
||
|
// Section 3. Define the fonts that are to be used here
|
||
|
//
|
||
|
// ##################################################################################
|
||
|
|
||
|
// Comment out the #defines below with // to stop that font being loaded
|
||
|
// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
|
||
|
// normally necessary. If all fonts are loaded the extra FLASH space required is
|
||
|
// about 17Kbytes. To save FLASH space only enable the fonts you need!
|
||
|
|
||
|
#define LOAD_GLCD // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
|
||
|
#define LOAD_FONT2 // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
|
||
|
#define LOAD_FONT4 // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
|
||
|
#define LOAD_FONT6 // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
|
||
|
#define LOAD_FONT7 // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
|
||
|
#define LOAD_FONT8 // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
|
||
|
//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
|
||
|
#define LOAD_GFXFF // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
|
||
|
|
||
|
// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
|
||
|
// this will save ~20kbytes of FLASH
|
||
|
#define SMOOTH_FONT
|
||
|
|
||
|
|
||
|
// ##################################################################################
|
||
|
//
|
||
|
// Section 4. Other options
|
||
|
//
|
||
|
// ##################################################################################
|
||
|
|
||
|
// Define the SPI clock frequency, this affects the graphics rendering speed. Too
|
||
|
// fast and the TFT driver will not keep up and display corruption appears.
|
||
|
// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
|
||
|
// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
|
||
|
// With an ILI9163 display 27 MHz works OK.
|
||
|
|
||
|
// #define SPI_FREQUENCY 1000000
|
||
|
// #define SPI_FREQUENCY 5000000
|
||
|
// #define SPI_FREQUENCY 10000000
|
||
|
// #define SPI_FREQUENCY 20000000
|
||
|
// #define SPI_FREQUENCY 27000000
|
||
|
// #define SPI_FREQUENCY 40000000
|
||
|
// #define SPI_FREQUENCY 55000000 // STM32 SPI1 only (SPI2 maximum is 27MHz)
|
||
|
#define SPI_FREQUENCY 80000000
|
||
|
|
||
|
// Optional reduced SPI frequency for reading TFT
|
||
|
#define SPI_READ_FREQUENCY 20000000
|
||
|
|
||
|
// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
|
||
|
#define SPI_TOUCH_FREQUENCY 2500000
|
||
|
|
||
|
// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
|
||
|
// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
|
||
|
// then uncomment the following line:
|
||
|
#define USE_HSPI_PORT
|
||
|
|
||
|
// Comment out the following #define if "SPI Transactions" do not need to be
|
||
|
// supported. When commented out the code size will be smaller and sketches will
|
||
|
// run slightly faster, so leave it commented out unless you need it!
|
||
|
|
||
|
// Transaction support is needed to work with SD library but not needed with TFT_SdFat
|
||
|
// Transaction support is required if other SPI devices are connected.
|
||
|
|
||
|
// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
|
||
|
// so changing it here has no effect
|
||
|
|
||
|
// #define SUPPORT_TRANSACTIONS
|