79 lines
3.2 KiB
C
79 lines
3.2 KiB
C
|
#define DISABLE_ALL_LIBRARY_WARNINGS
|
||
|
|
|
||
|
|
#define ST7789_DRIVER // Full configuration option, define additional parameters below for this display
|
||
|
|
// modified by ZH
|
||
|
|
// only needed for TESTING proper config file
|
||
|
|
#define ZH_ST7789_DRIVER_TESTING
|
||
|
|
|
||
|
|
#define TFT_WIDTH 240 // ST7789 240 x 240 and 240 x 320
|
||
|
|
#define TFT_HEIGHT 240 // ST7789 240 x 240
|
||
|
|
// added by ZH
|
||
|
|
// 7 pins: 4 defined here, 3 defined in script (or 2 as GND is ... ;-) )
|
||
|
|
#define TFT_DC 9 // DC on board - Data Command control pin
|
||
|
|
#define TFT_RST 8 // RES on board - Reset pin (could connect to RST pin)
|
||
|
|
#define TFT_MOSI 7 // SDA on board
|
||
|
|
#define TFT_SCLK 6 // SCL on board
|
||
|
|
// these 2 are not in use (touch screen only MISO, CS not needed/not available)
|
||
|
|
#define TFT_MISO 40 // not in use, use -1 if not in use or 40 better as it does not complain then
|
||
|
|
#define TFT_CS 40 // N/A on board - Chip select control pin, use -1 if not in use or 40 as it does not complain then
|
||
|
|
// BLK on board: backlight - LED - set in script not here
|
||
|
|
// VCC on board: power - set in script or direct to 3.3V/5V
|
||
|
|
// GND ... ;-)
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
#define LOAD_GLCD // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
|
||
|
|
#define LOAD_FONT2 // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
|
||
|
|
#define LOAD_FONT4 // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
|
||
|
|
#define LOAD_FONT6 // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
|
||
|
|
#define LOAD_FONT7 // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:.
|
||
|
|
#define LOAD_FONT8 // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
|
||
|
|
//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
|
||
|
|
#define LOAD_GFXFF // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
|
||
|
|
|
||
|
|
#define SMOOTH_FONT
|
||
|
|
|
||
|
|
|
||
|
|
// #define SPI_FREQUENCY 27000000
|
||
|
|
#define SPI_FREQUENCY 40000000
|
||
|
|
|
||
|
|
#define SPI_READ_FREQUENCY 20000000
|
||
|
|
|
||
|
|
#define SPI_TOUCH_FREQUENCY 2500000
|
||
|
|
|
||
|
|
// #define SUPPORT_TRANSACTIONS
|
||
|
|
|
||
|
|
// oldasy:
|
||
|
|
// ST7789 240 x 240 display with no chip select line
|
||
|
|
// #define USER_SETUP_ID 24
|
||
|
|
|
||
|
|
// #define ST7789_DRIVER // Configure all registers
|
||
|
|
|
||
|
|
// #define TFT_WIDTH 240
|
||
|
|
// #define TFT_HEIGHT 240
|
||
|
|
|
||
|
|
// //#define TFT_RGB_ORDER TFT_RGB // Colour order Red-Green-Blue
|
||
|
|
// //#define TFT_RGB_ORDER TFT_BGR // Colour order Blue-Green-Red
|
||
|
|
|
||
|
|
// //#define TFT_INVERSION_ON
|
||
|
|
// //#define TFT_INVERSION_OFF
|
||
|
|
|
||
|
|
// // DSTIKE stepup
|
||
|
|
// //#define TFT_DC 23
|
||
|
|
// //#define TFT_RST 32
|
||
|
|
// //#define TFT_MOSI 26
|
||
|
|
// //#define TFT_SCLK 27
|
||
|
|
|
||
|
|
// // Generic ESP32 setup
|
||
|
|
// //#define TFT_MISO 19
|
||
|
|
// //#define TFT_MOSI 23
|
||
|
|
// //#define TFT_SCLK 18
|
||
|
|
// //#define TFT_CS -1 // Not connected
|
||
|
|
// //#define TFT_DC 2
|
||
|
|
// //#define TFT_RST 4 // Connect reset to ensure display initialises
|
||
|
|
|
||
|
|
// // For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
|
||
|
|
// #define TFT_CS -1 // Define as not used
|
||
|
|
// #define TFT_DC PIN_D1 // Data Command control pin
|
||
|
|
// #define TFT_RST PIN_D4 // TFT reset pin (could connect to NodeMCU RST, see next line)
|
||
|
|
// //#define TFT_RST -1 // TFT reset pin connect to NodeMCU RST, must also then add 10K pull down to TFT SCK
|