#define DISABLE_ALL_LIBRARY_WARNINGS

#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
// modified by ZH 
// only needed for TESTING proper config file
#define ZH_ST7789_DRIVER_TESTING

#define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
#define TFT_HEIGHT 240 // ST7789 240 x 240
// added by ZH
// 7 pins: 4 defined here, 3 defined in script (or 2 as GND is ... ;-) )
#define TFT_DC      9   // DC on board - Data Command control pin
#define TFT_RST     8   // RES on board - Reset pin (could connect to RST pin)
#define TFT_MOSI    7   // SDA on board
#define TFT_SCLK    6   // SCL on board
// these 2 are not in use (touch screen only MISO, CS not needed/not available)
#define TFT_MISO    40  // not in use, use -1 if not in use  or 40 better as it does not complain then
#define TFT_CS      40  // N/A on board - Chip select control pin, use -1 if not in use   or 40 as it does not complain then
// BLK on board: backlight - LED - set in script not here
// VCC on board: power - set in script or direct to 3.3V/5V
// GND ... ;-)



#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:.
#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts

#define SMOOTH_FONT


// #define SPI_FREQUENCY  27000000
#define SPI_FREQUENCY  40000000

#define SPI_READ_FREQUENCY  20000000

#define SPI_TOUCH_FREQUENCY  2500000

// #define SUPPORT_TRANSACTIONS

// oldasy:
// ST7789 240 x 240 display with no chip select line
// #define USER_SETUP_ID 24

// #define ST7789_DRIVER     // Configure all registers

// #define TFT_WIDTH  240
// #define TFT_HEIGHT 240

// //#define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
// //#define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red

// //#define TFT_INVERSION_ON
// //#define TFT_INVERSION_OFF

// // DSTIKE stepup
// //#define TFT_DC    23
// //#define TFT_RST   32
// //#define TFT_MOSI  26
// //#define TFT_SCLK  27

// // Generic ESP32 setup
// //#define TFT_MISO 19
// //#define TFT_MOSI 23
// //#define TFT_SCLK 18
// //#define TFT_CS    -1 // Not connected
// //#define TFT_DC    2
// //#define TFT_RST   4  // Connect reset to ensure display initialises

// // For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
// #define TFT_CS   -1      // Define as not used
// #define TFT_DC   PIN_D1  // Data Command control pin
// #define TFT_RST  PIN_D4  // TFT reset pin (could connect to NodeMCU RST, see next line)
// //#define TFT_RST  -1    // TFT reset pin connect to NodeMCU RST, must also then add 10K pull down to TFT SCK